Search Results

To meet stringent emission standards, a considerable amount of development work is necessary to ensure suitable efficiency and durability of catalyst systems. The main challenge is to reduce the engine cold-start emissions. Close-coupled catalyst (CCC) provides fast light-off time by utilizing the energy in the exhaust gas. However, if some malfunction occurred during engine operation and the catalyst temperature exceeds 1050°C, the catalytic converter becomes deactivated and shows poor conversion efficiency. Close-coupled catalyst temperature was investigated under various engine operating conditions. All of the experiments were conducted with a 1.0L SI engine at 1500-4000 rpm. The engine was operated at no load to full load conditions. Exhaust gas temperature and catalyst temperature were measured as a function of lambda value (0.8-1.2), ignition timing (BTDC 30°-ATDC 30°) and misfire rates (0-28%).

Combustion and flame propagation characteristics of the liquid phase LPG injection (LPLI) engine were investigated in a single cylinder optical engine. Lean burn operation is needed to reduce thermal stress of exhaust manifold and engine knock in a heavy duty LPG engine. An LPLI system has advantages on lean operation. Optimized engine design parameters such as swirl, injection timing and piston geometry can improve lean burn performance with LPLI system. In this study, the effects of piston geometry along with injection timing and swirl ratio on flame propagation characteristics were investigated. A series of bottom-view flame images were taken from direct visualization using a UV intensified high-speed CCD camera. Concepts of flame area speed, in addition to flame propagation patterns and thermodynamic heat release analysis, was introduced to analyze the flame propagation characteristics.

Spray characteristics of diesel fuel injection is one of the most important factors in diesel combustion and pollutant emissions especially in HSDI (High Speed Direct Injection) diesel engines where the interval between the evaporation of atomized fuel and the onset of combustion is relatively short. An investigation into various spray characteristics from different holes of VCO nozzles was performed and its results were compared to standard sac nozzle. The global characteristics of spray, including spray angle, spray tip penetration, and spray pattern were measured from the spray images which were frozen by an instantaneous photography with a spark light source. For better understanding of spray behavior, SMD of the fuel sprays from each hole in the multi hole nozzles were measured with back light imaging while the sprays from the other holes were covered by a purpose-built nozzle cap.

The concentrations of individual exhaust hydrocarbon species were measured as a function of air-fuel ratio and EGR in a 2-liter four-cylinder engine using a gas chromatography, for natural gas and LPG. NMHC in addition to the species of HC, other emissions such as CO2, CO and NOx were at 1800rpm for two compression ratios (8.6 and 10.6) and various EGR ratios up to 7%. Fuel conversion efficiencies were also investigated together with emissions to study the effect of engine parameters on the combustion performances in gas engines especially under the lean burn conditions. It was found that CO2 emission decreased leaner mixture strength, the higher compression ratio and certainly with smaller C value of fuel. HC emissions from LPG engine consisted primarily of propane (larger 60%), ethylene and propylene, while main emissions from natural gas were methane (larger than 60%), ethane, ethylene and propane on the average.

Cryopreservation of the biological sample usually requires rapid cooling in order to suppress the growth of intracellular ice and to reach the temperature below the vitrification temperature. The ultra-rapid cooling technique by using liquid nitrogen is favorable because it is safe, inexpensive, and harmless in most cases. This paper describes the transient heat transfer phenomena when the object is suddenly plunged into subcooled liquid nitrogen. The heat transfer coefficient in this rapid cooling process is very different from that of the steady state boiling where the quasi-static approximation is made. The cooling experiment used 0.2 mm thick copper disk. The temperature history was precisely measured during cooling process under various subcooled conditions (from 65 K to 77 K) of liquid nitrogen. The data is used not only for analyzing the cooling rate but also for estimating the instantaneous heat transfer coefficients.

Experiments were performed with a 4-stroke, natural gas fueled SI engine to investigate the effects of several parameters on engine performance under lean operating condition. A favorable effect of charge swirl on stable lean burn operation was observed at a conventional compression ratio. There was an optimum EGR rate which gave a substantial reduction in NOx emissions with minor penalties in efficiency and UHC emissions. Marginal improvement was noticed with lean operations in a long spark duration ignition system. The flame jet ignition system displayed noticeable capability in extending the lean limit. In addition, shadowgraph visualization tests were performed for combustion diagnostic purposes.